Keg Dispensing Supplies

Use your CO2 regulator with a beer gas tank with this CO2 regulator to nitrogen adapter! This part is approximately 3 inches long and will adapt a female CGA-320 fitting (which is the standard fitting on a standard CO2 regulator) to a male CGA-580 fitting (which is the standard fitting on a beer gas tank). This way, you will be able to use your existing CO2 regulator on a beer gas tank without buying a new nitrogen regulator! This works great for the creamy beer enthusiast who occasionally uses beer gas! Please note that this connection should NOT be used with pure nitrogen due to the higher pressures that pure nitrogen is kept under. This should work great for most people who occasionally use beer gas to give their beers that extra creaminess!

Taprite has long been a trusted name in the beverage industry. Known for their high quality craftsmanship, Taprite has one of the best regulators on the market! These dual guage regulators have a low pressure gauge which shows output pressure (supports 0 - 50 PSI), and a high pressure gauge that shows the remaining pressure in the cylinder. Taprite regulators are known for having high quality diaphragms which stand up to the test of time much better than cheaper or lower-quality regulators, as well as being more accurate for a longer period of time. The regulator also includes a standard CO2 barb with shutoff valve and a safety check.

Oetiker clamps provide a permanent clamping solution! This style of clamp has a 1-ear design, which means they are crimped at a single point on the clamp to create a superior seal over your tubing. These large Oetiker clamps are often used on 5/16" thick-walled tubing that is used in CO2 connections on kegging and draft systems. These clamps hold tight, creating a great seal that holds for a long time! Some people prefer these for more permanent systems. If you are looking to switch over to a snug seal that lasts, make sure you use Oetiker clamps!

Beer shanks to make all your dispensing dreams come true! These chrome plated brass shanks are used in a variety of setups to create draft systems. A 3/16" bore is perfect for liquid dispensing of all types, including sweet sweet beer. This 4" shank is a standard size (actual measurement is 4 1/8") and works on most applications. Simply drill out your hole, place your shank through, and lock in place with the included lock nut. A faucet can then be attached to the outside of your draft setup, whether it be a kegerator, keezer or jockey box! Also needed on the inside is a 3/16" tailpiece, neoprene beer washer and beer nut.

Long and narrow, the dip tube brush was made specifically for cleaning out keg dip tubes. Being long and narrow themselves, dip tubes can be tricky to clean properly without the right tool. Cleaning out a dip tube with a dip tube brush ensures that you scrub the whole inner surface of the dip tube, where bacteria and beer stone can easily hide. These brushes are also good for cleaning sight glasses and other narrow brewing equipment. Another brush highly recommended to anyone who owns a keg!

These check valves are the perfect solution to backflow issues that you may be having. They go on the gas side of a ball or pin lock gas system. They have an integrated back check valve that helps prevent flow from reversing, and fit on the 1/4" MFL fitting found on most standard ball or pin lock disconnects. Keep your gas lines clean with these as a preventative measure.

This is a male compression nut for beer towers. It goes in the end of a shank and accomodates a liquid tower elbow to get the beer flowing! You may also need a tower grommet to help create a good seal. With these, you should have the beer flowing from your tower in no time!

This is a replacement washer for the lever on the old 425 series Perlick faucets. If your old faucet is in need of some new washers, we've got you covered! These are the perfect replacement for old, disused Perlick 425 series faucets.

Turn your fridge into a kegerator with our kegerator homebrew kegging system! This system comes with all the internal workings of a kegerator system you will need, except the CO2 cylinder.

Included is a high quality Taprite regulator, ball lock gas line assembly, a brand new 5 gallon cornelius keg, a ball lock liquid disconnect with swivel nut set, 6 feet of 3/16" ID Bevlex thick-walled liquid tubing, and a full shank assembly that includes a standard beer faucet, faucet knob, 4" shank, 1/4" tailpiece, beer nut and neoprene washer. Make the draft system you have always wanted with this kegerator kegging system, complete with a brand spankin' new keg!

All you'll need in addition to this kit to make the ultimate kegerator, is a full CO2 tank. For local customers we sell full tanks at all of our retail locations!

3" Chrome Dual Tap Tower

Chrome replacement collar for the Perlick Perl faucet.

This is the ball needed for the Guiness "U" coupler which prevents backflow. As opposed to the check valve ball on a standard keg, the ball found in the Guiness coupler is slightly larger. Make sure you have the right one for your coupler!

This is the part that really gets the beer flowing! Chrome-plated brass construction ensures for longevity of the coupler, so that you can keep the beer flowing keg after keg. This "D" style coupler is the standard coupler used by virtually all American and Canadian breweries, and as such, this is the most convenient keg coupler to own in North America. One of these allows you to tap almost any keg from any American or Canadian breweries. This coupler comes with a standard 5/16" gas barb, check valve and beer nut on the gas side. Not included with this coupler are the neoprene washer, 3/16" barb liquid tailpiece and beer nut.

Want to make your own kegerator? Have a tower that you need replaced? Great Fermentations offers these 3" beer towers for all your tower needs! This model is a standard 3" model, which works well as a replacement on kegerators that have the same sized tower. It has a single beer faucet attached to the tower. If you are making your own kegerator, you can affix this to the top of a dorm fridge or other small refridgerator. Just like that, you've got yourself a kegerator! The sleek chrome finish looks nice as your pour the perfect beer from the tower. Cheers!

Most keg couplers work the same, with many similar parts. The Guiness "U" coupler is no exception. It too has a check valve ball and a retainer for the ball. The Guiness ball and retainer are, however, different, and thus require different replacement parts that the reguilar. If you are in need of a new check valve retainer for your Guiness coupler, look no further than Great Fermentations!

This replacement o-ring fits on Perlick faucets. It is the o-ring that seals the lever component of the faucet. Integral in the proper functioning of these Perlick faucets, it is never a bad idea to have an extra on hand!

Party Pig Valve Assem with gasket

Three is better than one! This 3" beer tower extension not only extends your tower, but comes with two shanks for adding two more faucets to your tower setup. With the existing fauet, this means that you can have up to three beer faucets on your setup! Perfect for going big with your existing 3" beer tower, get your extension today!

This is a replacement black lever washer for standard faucets. It goes on top of the white faucet shaft washer on the faucet lever of a standard faucet. Washers wear out over time, and used equipment that has not been properly maintained may need new washers. If this is the case, Great Fermentations has replacements for you!

Chrome Bonnet for Perlick Forward Faucet

Need new o-rings for the inside of your stout faucet? Look no further! Great Fermentations have these o-rings available to you so that you can keep those creamy beers flowing! These o-rings fit in the body of the faucet above the nozzle and keep everything tight and secure. Have a few on hand so you'll always be prepared for the inevitable!